Hopkins 12-Volt Power Socket Installation - 2012 Honda CR-V- Video
Hey everybody, Ryan here at etrailer. Today on our 2012 Honda CR-V, we're gonna be taking a look at, and showing you how to install the Hopkins 12 volt power outlet kit. So right away, here's what the 12 volt power outlet is going to look like. You know, pretty standard. Kind of just has your standard, you know, cigarette type port there, that you can plug different accessories into. Now, let's kind of talk about why you need this. more
9/2/2021 8:33:26 AM
Roadmaster 12 Volt Outlet Kit Installation - 2012 Honda CR-V- Video
Speaker 1: Today on our 2012 Honda CR-V we're going to be installing Roadmaster's 12 Volt Outlet Kit, part number RM-9332.This 12 volt outlet kit is going to give you a quick interface to work with your typical automobile auxiliary connectors. You can hook it up however you'd like. You could have it so it's powered all the time regardless of your ignition switch position, or you could wire it up to one of your ignition switch positions, whether it be accessory or run position. Depending how you have it wired up, it can be used for a lot of different things. Currently, ours is wired up to be powered all the time, and we're using it in our flat tow setup to ensure that our braking system always has power and is operational.Now, there are some other things you may want to use it for. Let's say you've got a set of seat heaters that you installed in your vehicle, aftermarket seat heaters that run off these, and you want inaudible 00:00:51 seat heater make sure that it turns off when you shut your vehicle off so it doesn't drain your battery. more
11/9/2018 11:22:12 AM
Roadmaster 12 Volt Outlet Kit Installation - 2010 Honda CR-V- Video
Today on our 2010 Honda CRV we'll be taking a look at installing the 20 amp 12 volt out-leg kit, part number RM-9332. Now we have our 12 volt power ready to use whenever we need it for our auxiliary braking system for our towed vehicle. Now when we don't have any use you can put it up here in the holder or we can also place it down back underneath the back side of the stream panel making sure that it doesn't fall down while we're driving. On one end we're going to have our fuse and spade connector and on the other end we're going to have to make ground around that ring terminal there. Both of the pieces that we're going to need are going to be included in the kit. So right now we're going to find a fuse that has power going through it so we can run our constant power towards our 12 volt circuit. So go up underneath the dash and locate that fuse panel that's sitting right here right above this kick panel on the side. Now we're just going to locate a fuse, it gives us the ability to draw power when our key is not in the ignition. more
10/22/2015 3:07:31 PM
Roadmaster 12 Volt Outlet Kit Installation - 2014 Honda CR-V- Video
All right, today in a 2014 Honda CR-V, we're going to install part number RM-9332. This is 12-O outlet kit, ready for 20 amps. Right now outlet kit is designed to work with the fuse panel. In this case we're going to use a fuse that's underneath the dash. If you're in a vehicle set up to be pulled behind an RV, we'll go ahead and look for a fuse. Now in this case, our key will be in the first notch when you turn it. So, we'll go ahead and use a fuse. In this case, we're going to test fuse number 14, which is easy to get to, and it's just your seat heaters. more
8/27/2014 2:47:39 PM
WagenTech Power Inverter Installation - 2011 Honda Pilot- Video
Today on this 2011 Honda Pilot were going to install Wagan Techs Power Inventer, part number 02294. Now the wiring that comes with the inverter is not really long enough to reach up to the battery, so were going to use an additional kit to supply the necessary components and were actually using part number SW1520 from Superwinch, this here auxiliary wire harness. First thing were going to do is go ahead and show where were going to place our inverter. Were actually going to place underneath the passenger side seat. Now you can see how it sits a little bit crooked in there and theres a cut in the carpet already. So what were going to do is push it up against that one side of the carpet cut and we go to other side to make another cut where it will sit flat. more
2/2/2012 9:46:32 AM
Filter Videos
Filter Videos
